SPUHR 35mm PICATINNEY MOUNT 0MIL/0MOA - 1.50"
The IDEAL SCOPE MOUNT SYSTEM series of mounts features seven sets of interfaces to attach any of more than 40 different accessories, and has a bubble level integrated in the rear plane of the mount body to prevent canting of the rifle. The rings are diagonally cut for increased visibility of the elevation and windage turrets (US Patent 8,733,011).

FEATURES
The mount is shipped with a manual and a "wedge" leveling key.
This simple tool fits in a 10-degree slot on the mount while mounting the scope and works against the bottom of the scope to ensure a perfectly level scope.

4 Numbered And Indexed Mounting Torx
Even the slightest variance in how the mount is attached to a weapon can alter the point of impact. To resolve this, the ISMS has numbered screw holes so you can attach the mount the same way each time. The amount of torque applied to the mount can also cause unwanted variance so Spuhr has placed index marks on the screw head so you can put the exact same amount of torque on your mount no matter how often you remove the mount.

Built In Level
With a quick glance from your left eye you can get an instant check of your level without leaving your shooting position. The built in level is always protected in the rear of the mount and is not a risk of shifting or being broken off on the move.

Accessory Interface
Every mount consists of 7-8 mounting interfaces where you can attach nearly anything. The interface consists of two threaded M4 holes that are depressed in a conical hole to perfectly fit the individual attachment interfaces (sold separately) with absolutely no play in the joint.

Durability
Prevents damage on scope due to flexing during heavy recoil or rough environment. The snipers rifle and the spotters carbine can have the same mount, enabling the use of same equipment and accessories. Rings are grooved inside to get a better grip of the scope and enabling gluing of the scope. The mount is milled out of one billet of material instead of being screwed together from small parts.

Scope Rotation
Patent pending solution for indexing the rotation of the scope, using an included tool/gauge to index the scope correctly to the mount and gun. Important since an incorrectly indexed scope unintentionally will also have a sideways adjusted point of impact and since it will be adjusted sideways when it is adjusted for elevation.

Mounting Placements
Traditionally lasers have been mounted on the forend of the rifle, a solution with drawbacks. For the same reasons you don′t want your barrel to touch the forend, you don′t want the sights to be mounted on the forend. Our mounting system has a minimum of seven interfaces for accessories and the laser can easily be mounted on the mount, giving the advantage of an undisturbed laser and a weight more central on the gun instead of forward.

Accessible and Readable Dials
The rings are cut 45 degrees instead of the usual horizontal, providing several advantages. The screws holding the parts together are not in the way of the knobs, thus the shooter can quickly determine the settings of the knobs. It also gives the shooter a horizontal line that helps the shooter not torotate his gun unintentionally. The rings have index marks on the top and right side, making low knobs more easily readable.

Accessories
Possibility of using various accessories such as angle cosine indicator, back up sights, lasers, illuminators, Night vision mounts etc. With traditional mounts this can be achieved only if there is sufficient space on the middle tube for additional rings, which there rarely is. Ideal Scope Mount Systems have interface surfaces directly on the mount, making it possible to mount accessories either by Picatinny rails or as direct interfaces for certain accessories such as angle cosine indicators and red dot sights. A selection of interfaces for popular accessories are available, and others can be made to specification.

Machined Mounts
The mounts are machined from billet 7075 T651 aluminum and all aluminum parts are hardcoat anodized. The Torx 20 ring and clamping screws are zinc-nickel coated for corrosion resistance. The screws come pre-waxed from the factory to ensure proper torque values.

SPECIFICATIONS
» Rings - 35 mm
» Tilt - 0 MIL/MOA
» Height - 38 mm/1.5"
» Length - 126 mm/4.96"
» Weight - 272 g/9.6 oz
» Interfaces - 7 sets


NOTE:
The SP-5002 is designed for use 56 mm objectives on rifles with MIL-STD-1913 or STANAG 4694 rails, and is especially suitable for extended Picatinny rails combined with night vision equipment. The SP-5002 will fit most 35 mm scope tubes except for scopes with extended erector housings, such as the US Optics TPAL/EREK.